發布時間：2019-06-21 07:23

【摘要】：某大橋橋塔采用門形框架結構,橋塔上橫梁為單箱單室預應力混凝土結構,高度7~19m,橫梁頂面寬度為8.565m。針對該橋橋塔上橫梁結構特點、施工難點及工期要求,上橫梁與上塔柱采用異步施工方案,待塔身施工完成后再施工上橫梁。該橋塔上橫梁采用型鋼托架方法進行施工。為了保證上橫梁在施工中的安全,建立了托架的有限元模型,從強度、剛度及穩定性等方面對該托架進行了驗算,同時考慮橋塔與托架的相互作用。分析結果表明:在最不利工況荷載作用下,上橫梁托架結構的強度、剛度、穩定性均滿足施工要求。
[Abstract]:The tower of a bridge adopts portal frame structure. The beam on the tower is a single box and single chamber prestressed concrete structure with a height of 7 m and a width of 8.565 m at the top of the beam. According to the structural characteristics, construction difficulties and construction period requirements of the upper beam of the bridge tower, the asynchronous construction scheme is adopted between the upper beam and the upper tower column, and then the upper beam is constructed after the construction of the tower body is completed. The beam on the tower of the bridge is constructed by section steel bracket method. In order to ensure the safety of the upper beam in construction, the finite element model of the bracket is established, and the strength, stiffness and stability of the bracket are checked and calculated, and the interaction between the tower and the bracket is considered at the same time. The analysis results show that the strength, stiffness and stability of the upper beam bracket structure meet the construction requirements under the most unfavorable load.
【作者單位】： 湖南省大岳高速洞庭湖大橋建設開發有限公司;湖南中大設計院有限公司;
【分類號】：U445.4

【相似文獻】

相關期刊論文 前3條

1 王宇鴻;王健;王永逵;張人耀;;寧波某碼頭上橫梁混凝土的施工[J];商品混凝土;2006年02期

2 王福田;;大型水壓機上橫梁安裝精益求精[J];冶金建筑;1964年05期

3 常志軍;;南寧大沖邕江特大橋北岸索塔上橫梁施工技術[J];鐵道建筑技術;2014年S1期

相關碩士學位論文 前1條

1 王瀚;板桁結合斜拉橋鋼橋面板支撐體系受力分析及構造優化研究[D];長沙理工大學;2015年

，

本文編號：2503897