制冷型紅外探測器組件低溫熱特性研究
發布時間：2018-09-17 20:46
【摘要】：制冷型紅外探測器由于其靈敏度高、響應速度快、探測器距離遠等優點,廣泛應用于高端武器裝備中。由于應用于軍事領域,對制冷型紅外探測器組件的體積、重量、降溫時間、功耗及探測器可靠性等關鍵性能指標有嚴苛的要求。通過集成式探測器杜瓦制冷機組件的應用,可從機械結構上優化組件的體積、重量及功耗。對于組件降溫時間及探測器可靠性的優化途徑,需要通過制冷型紅外探測器組件的低溫熱學特性研究獲得。制冷型紅外探測器組件低溫熱學特性,主要指組件因需要在低溫下工作而產生的組件熱負載、降溫時間及探測器封裝后可靠性等問題。研究的主要內容包括:各因素對組件制冷降溫時間的影響規律、探測器封裝后熱適配優化方法及組件關鍵零部件熱特性優化技術等。本文針對制冷型紅外探測器組件低溫熱學特性的研究要求,闡明了課題的研究目標,通過理論分析和合理的驗證實驗以及開展相應關鍵零部件熱特性優化研究,獲得了制冷型紅外探測器組件相關低溫熱學特性的影響情況,并制備獲得相關熱特性優化的關鍵零部件。本文以320×256規格制冷型紅外探測器封裝用典型IDDCA組件為例,通過建立傳熱模型及理論分析,獲得了組件降溫時間的影響因素;通過開展降溫時間影響實驗,獲得了各因素對組件降溫時間的影響規律。本文以320×256規格制冷型紅外探測器典型封裝結構為例,通過ANSYS仿真分析,分析了在冷平臺機械結構一定情況下,膨脹系數對探測器的應力及應變影響情況,并根據應力最優化原則確定了冷平臺材料為因瓦4J36;開展了不同材料引線基板在封裝前后,對硅電路上表面的應變影響實驗,實驗結果表明平衡層結構及AlN陶瓷基板對探測器�？旆庋b后的額外應變較小。本文開展了關鍵零部件熱特性優化技術研究工作,通過合理的制備流程設計,制備獲得內表面黑化外表面鍍金的輻射漏熱優化電鑄冷屏,使組件在80K下熱負載降低約6.6mW;以K508制冷機為對象,開展了低漏熱、高強度集成式冷指的制備研究,制備獲得集成式冷指零件,與K508制冷機耦合后,在80K下獲得約610mW制冷量;開展了高熱導率、低膨脹系數的金屬復合材料制備研究,并以4J32材料作為基體,30%銅材料作為增強相。制備獲得φ21.7mm×0.6mm的金屬復合材料基片,其常溫下膨脹系數為2.23×10~(-6)K~(-1)、熱導率為34.67 W/(m·K)。
[Abstract]:Refrigerated infrared detectors are widely used in high-end weapons because of their high sensitivity, high response speed and long range. Because of its application in military field, the key performance indexes such as volume, weight, cooling time, power consumption and detector reliability are strictly required. Through the application of the integrated detector Dewar refrigerator assembly, the volume, weight and power consumption of the assembly can be optimized from the mechanical structure. To optimize the cooling time and the reliability of the detector, it is necessary to study the low temperature thermal characteristics of the refrigerated infrared detector module. The low temperature thermal characteristics of the refrigerated infrared detector module mainly refer to the thermal load, cooling time and the reliability of the detector package due to the assembly working at low temperature. The main contents of the research include: the influence of various factors on the cooling time of the module, the optimization method of the thermal adaptation after the detector packaging and the optimization technology of the thermal characteristics of the key parts of the module, etc. In this paper, according to the research requirements of the low temperature thermal characteristics of the refrigerated infrared detector assembly, the research objectives are clarified. The research results are analyzed by theoretical analysis and reasonable verification experiments, as well as the research on the optimization of the thermal characteristics of the corresponding key parts. The influence of the low temperature thermal characteristics of the refrigerated infrared detector assembly was obtained, and the key parts for the optimization of the related thermal characteristics were prepared. In this paper, taking the typical IDDCA module of 320 脳 256-specification refrigerated infrared detector package as an example, the factors influencing the cooling time of the module are obtained by establishing the heat transfer model and theoretical analysis, and the experiment of cooling down time is carried out. The effects of various factors on the cooling time of the components are obtained. In this paper, the typical packaging structure of 320 脳 256-specification refrigerated infrared detector is taken as an example, and the influence of expansion coefficient on the stress and strain of the detector is analyzed by ANSYS simulation analysis under the certain mechanical structure of the cold platform. According to the principle of stress optimization, the cold platform material was determined to be Involva 4J36, and the strain effect experiments of different material lead substrates on the upper surface of silicon circuit were carried out before and after packaging. The experimental results show that the extra strain of the balanced layer structure and the AlN ceramic substrate is small after the fast packaging of the detector mode. In this paper, the optimization technology of the thermal characteristics of key parts is studied. Through the reasonable preparation process design, the radiative heat leakage optimized electroforming cold screen is prepared to blacken the inner surface of the outer surface and plated the gold on the outer surface of the inner surface. The heat load of the assembly is reduced by about 6.6 MW at 80K, and the low heat leakage and high strength integrated cold finger is prepared by using K508 refrigerator as the object. The integrated cold finger parts are prepared and coupled with the K508 refrigerator, and the 610mW refrigerating capacity is obtained at 80K. The preparation of metal composites with high thermal conductivity and low coefficient of expansion was studied. The 4J32 material was used as the matrix and 30% copper as the reinforcement phase. The metal composite substrates with 蠁 21.7mm 脳 0.6mm were prepared. The expansion coefficient was 2.23 脳 10 ~ (-6) K ~ (-1) and the thermal conductivity was 34.67 W / (m K). At room temperature.
【學位授予單位】：中國科學院大學(中國科學院上海技術物理研究所)
【學位級別】：碩士
【學位授予年份】：2017
【分類號】：TN215
本文編號：2247042
[Abstract]:Refrigerated infrared detectors are widely used in high-end weapons because of their high sensitivity, high response speed and long range. Because of its application in military field, the key performance indexes such as volume, weight, cooling time, power consumption and detector reliability are strictly required. Through the application of the integrated detector Dewar refrigerator assembly, the volume, weight and power consumption of the assembly can be optimized from the mechanical structure. To optimize the cooling time and the reliability of the detector, it is necessary to study the low temperature thermal characteristics of the refrigerated infrared detector module. The low temperature thermal characteristics of the refrigerated infrared detector module mainly refer to the thermal load, cooling time and the reliability of the detector package due to the assembly working at low temperature. The main contents of the research include: the influence of various factors on the cooling time of the module, the optimization method of the thermal adaptation after the detector packaging and the optimization technology of the thermal characteristics of the key parts of the module, etc. In this paper, according to the research requirements of the low temperature thermal characteristics of the refrigerated infrared detector assembly, the research objectives are clarified. The research results are analyzed by theoretical analysis and reasonable verification experiments, as well as the research on the optimization of the thermal characteristics of the corresponding key parts. The influence of the low temperature thermal characteristics of the refrigerated infrared detector assembly was obtained, and the key parts for the optimization of the related thermal characteristics were prepared. In this paper, taking the typical IDDCA module of 320 脳 256-specification refrigerated infrared detector package as an example, the factors influencing the cooling time of the module are obtained by establishing the heat transfer model and theoretical analysis, and the experiment of cooling down time is carried out. The effects of various factors on the cooling time of the components are obtained. In this paper, the typical packaging structure of 320 脳 256-specification refrigerated infrared detector is taken as an example, and the influence of expansion coefficient on the stress and strain of the detector is analyzed by ANSYS simulation analysis under the certain mechanical structure of the cold platform. According to the principle of stress optimization, the cold platform material was determined to be Involva 4J36, and the strain effect experiments of different material lead substrates on the upper surface of silicon circuit were carried out before and after packaging. The experimental results show that the extra strain of the balanced layer structure and the AlN ceramic substrate is small after the fast packaging of the detector mode. In this paper, the optimization technology of the thermal characteristics of key parts is studied. Through the reasonable preparation process design, the radiative heat leakage optimized electroforming cold screen is prepared to blacken the inner surface of the outer surface and plated the gold on the outer surface of the inner surface. The heat load of the assembly is reduced by about 6.6 MW at 80K, and the low heat leakage and high strength integrated cold finger is prepared by using K508 refrigerator as the object. The integrated cold finger parts are prepared and coupled with the K508 refrigerator, and the 610mW refrigerating capacity is obtained at 80K. The preparation of metal composites with high thermal conductivity and low coefficient of expansion was studied. The 4J32 material was used as the matrix and 30% copper as the reinforcement phase. The metal composite substrates with 蠁 21.7mm 脳 0.6mm were prepared. The expansion coefficient was 2.23 脳 10 ~ (-6) K ~ (-1) and the thermal conductivity was 34.67 W / (m K). At room temperature.
【學位授予單位】：中國科學院大學(中國科學院上海技術物理研究所)
【學位級別】：碩士
【學位授予年份】：2017
【分類號】：TN215
【參考文獻】
相關期刊論文 前10條
1 曾婧;彭超群;王日初;王小鋒;;電子封裝用金屬基復合材料的研究進展[J];中國有色金屬學報;2015年12期
2 尹爽;朱穎峰;黃一彬;張嫻靜;趙維艷;徐思軼;;紅外焦平面杜瓦冷屏擋光環雜散輻射的抑制[J];紅外技術;2015年11期
3 陳星;華樺;何凱;王建新;葉振華;張勤耀;;紅外焦平面探測器封裝結構熱應力分析[J];激光與紅外;2014年06期
4 朱穎峰;韓福忠;李東升;黃一彬;毛京湘;;快速制冷啟動的中波320×256紅外焦平面探測器研究[J];紅外與激光工程;2014年04期
5 劉辰;;托克馬克冷屏表面超低溫發射率實驗研究[J];低溫與超導;2014年03期
6 史衍麗;;第三代紅外探測器的發展與選擇[J];紅外技術;2013年01期
7 高興勇;陸蘊香;;大型圓柱體鋼錠加熱時間計算的集總熱容法應用[J];冶金能源;2011年03期
8 王小坤;曾智江;朱三根;李言謹;胡曉寧;何力;丁瑞軍;;中波2048元長線列碲鎘汞焦平面杜瓦組件[J];紅外與激光工程;2011年04期
9 李言謹;;降低紅外焦平面熱失配應力方法[J];科技導報;2011年08期
10 李建林;周效軍;;利用流量法測量微型金屬杜瓦瓶熱負載及其計算方法[J];紅外與激光工程;2011年01期
相關博士學位論文 前2條
1 趙揚;石墨烯結構調控、功能組裝及其應用研究[D];北京理工大學;2015年
2 陳星;碲鎘汞紅外焦平面探測器可靠性相關技術研究[D];中國科學院研究生院（上海技術物理研究所）;2014年
相關碩士學位論文 前1條
1 李雪;紅外探測器冷屏件高輻射紅外吸收涂鍍層研究[D];昆明理工大學;2014年
，本文編號：2247042
本文鏈接：http://www.wukwdryxk.cn/kejilunwen/dianzigongchenglunwen/2247042.html
