發布時間：2018-06-18 14:34

  本文選題：串口 + TCP/IP協議��； 參考：《東華大學》2017年碩士論文

【摘要】：工業大數據的基礎是數據來源的準確性。傳統的零件尺寸數據檢測方法是先通過測量儀器進行測量,然后手工記錄再輸入上位機,此模式不僅人力成本高,還會增加出錯率。與此同時,隨著以太網技術的發展,基于以太網的網絡互聯設備的使用也開始越來越普及。在這個背景下,工業互聯網及工業4.0的提出使工業的發展突破傳統“制造”的內涵,并讓制造和生產更加智能化和低成本化,這在人力成本日益增加的今天,對于企業的擴大產能和健康發展具有非常重要的意義。盡管讓所有設備都能連入互聯網已成為一種趨向,但設備通信互聯的模式仍在不斷發展和進步。串行通信的可靠性和安全性較高,傳輸協議也相對簡單,在近距離的數據通信中容易實現,正是由于上述特點,RS-232/RS-485等異步串行接口廣泛應用于很多終端設備。但是串行通信存在無法與距離傳輸,無法接入主流網絡等缺點,并且串行通信連接的接頭不支持帶電插拔,這給調試過程也帶來諸多不便。而零件尺寸數據的采集,不僅是為了判斷生產的零件是否合格,也為了對零件尺寸數據進行相關分析并且用以反饋以及調整生產情況�？纵S匹配就是零件數據分析中的一個重要問題,傳統的解決方法普遍是任意匹配或分組匹配,這種策略在對精度要求很高的場合很難兼顧匹配精度和成本。本文的研究基于目前行業中零件的數據采集與分析中現實問題以及大部分測量設備集成了串口且未聯網的現狀展開。本文的多串口轉以太網的數據采集及分析系統可以在無需更換傳統檢測設備的基礎上,實現將串行通信檢測設備的串行通信數據通過以太網實時傳輸,這可以解決串行通信本身無法與距離傳輸?shù)膯栴},實現串口設備的監控與網絡化管理,并且可以對采集到的孔軸數據進行孔軸匹配分析。本文提出了多串口轉以太網的數據采集及分析系統的總體架構,并采用邁沖科技公司設計的MC-A5D3X-GKA底板以及MC-A5D3X-CORE核心板為硬件載體,使用基于嵌入式Linux的軟件系統實現串口數據到以太網的傳輸,利用C#開發上位機軟件實現采集數據的實時顯示和已采集數據的查詢,使用SQL SERVER2012數據庫作為后臺數據存儲及前端數據展示的媒介。對采集到的合格的孔軸直徑數據,提出用智能優化算法中的遺傳算法對孔軸匹配問題進行優化,以達到同批量孔軸對匹配成功的對數最多,并在匹配對數最多的情況下讓孔軸間間隙最小的優化結果,與傳統人工匹配的結果相比,在確保匹配精度基礎上,大大提高了匹配率。同時,有效的匹配也在一定程度上降低了孔軸加工過程的偏差要求。
[Abstract]:The industrial big data is based on the accuracy of data sources. The traditional method of measuring part size data is first measured by measuring instrument, then recorded by hand and then input into the upper computer. This mode not only has high labor cost, but also increases the error rate. At the same time, with the development of Ethernet technology, the use of network interconnection devices based on Ethernet is becoming more and more popular. In this context, the introduction of Industrial Internet and Industrial 4.0 makes the development of industry break through the connotation of traditional "manufacturing" and make manufacturing and production more intelligent and low-cost. For the expansion of capacity and healthy development of enterprises have a very important significance. Although it has become a trend to connect all devices to the Internet, the mode of device communication interconnection is still developing and improving. The serial communication has high reliability and security, and the transmission protocol is relatively simple. It is easy to realize in the short distance data communication. It is precisely because of the above characteristics that the asynchronous serial interface such as RS-232 / RS-485 is widely used in many terminal devices. However, the serial communication has some disadvantages, such as unable to transmit distance, unable to connect to the mainstream network, and the connection of serial communication does not support live plugging, which brings many inconvenience to the debugging process. The acquisition of part dimension data is not only to judge whether the part is qualified, but also to analyze the part dimension data and to feedback and adjust the production situation. Hole shaft matching is an important problem in part data analysis. The traditional solution is arbitrary matching or grouping matching. This strategy is difficult to match precision and cost when the precision is very high. The research of this paper is based on the practical problems of data acquisition and analysis of parts in the industry and the fact that most of the measuring devices are integrated with serial port and are not connected to the network. The data acquisition and analysis system of multi-serial port to Ethernet in this paper can realize the real-time transmission of serial communication data through Ethernet on the basis of no need to replace the traditional detecting equipment. This can solve the problem that the serial communication itself can not transmit the distance, realize the monitoring and network management of the serial port equipment, and can carry on the hole axis matching analysis to the collected hole axis data. In this paper, the architecture of data acquisition and analysis system of multi-serial port to Ethernet is presented. The MC-A5D3X-GKA bottom board and MC-A5D3X-CORE core board are used as the hardware carrier, and the MC-A5D3X-GKA core board is used as the hardware carrier. The software system based on embedded Linux is used to realize the transmission of serial port data to Ethernet, and C # is used to develop the upper computer software to realize the real-time display of the collected data and the query of the collected data. SQL SERVER2012 database is used as the media of background data storage and front-end data display. For the qualified hole shaft diameter data collected, the genetic algorithm in the intelligent optimization algorithm is proposed to optimize the hole shaft matching problem in order to achieve the maximum logarithm of the matching success in the same batch of hole shaft pairs. In the case of maximum matching logarithm, the optimal result of minimizing the gap between the holes is compared with the traditional artificial matching results, and the matching rate is greatly improved on the basis of ensuring the matching accuracy. At the same time, the effective matching also reduces the deviation requirement of the hole shaft machining process to some extent.
【學位授予單位】：東華大學
【學位級別】：碩士
【學位授予年份】：2017
【分類號】：TP274.2

【參考文獻】

相關期刊論文 前10條

1 王璐;;工業大數據激活智能制造[J];軟件和集成電路;2016年08期

2 趙福全;劉宗巍;;工業4.0浪潮下中國制造業轉型策略研究[J];中國科技論壇;2016年01期

3 孫曉曄;成彬;;串口轉以太網模塊配置軟件設計及實現[J];微型機與應用;2015年22期

4 王建民;;智能制造基礎之工業大數據[J];機器人產業;2015年03期

5 胡晶;;工業互聯網、工業4.0和“兩化”深度融合的比較研究[J];學術交流;2015年01期

6 張曙;;工業4.0和智能制造[J];機械設計與制造工程;2014年08期

7 王海勇;;基于ARM9的嵌入式多串口服務器設計[J];化工自動化及儀表;2013年03期

8 董武;陸利坤;李業麗;;基于W5300的以太網和串口數據相互轉換系統設計[J];制造業自動化;2013年02期

9 李紅嬋;朱顥東;;采用十進制免疫遺傳算法求解高校排課問題[J];系統工程理論與實踐;2012年09期

10 曾廣圣;曾維清;徐冉;;一種基于ARM的以太網串口服務器的設計[J];科技廣場;2012年05期

相關碩士學位論文 前8條

1 吳榮斌;基于ARM9的以太網串口服務器的設計與實現[D];蘭州交通大學;2014年

2 楊洋;基于ARM的多串口服務器系統[D];昆明理工大學;2014年

3 葉晶;服裝數控裁床裁剪路徑優化的研究[D];蘇州大學;2014年

4 周超;基于Cortex-M3的以太網串口服務器的設計與實現[D];武漢理工大學;2012年

5 袁成文;基于MC9S12NE64的通用串口以太網轉換器[D];昆明理工大學;2011年

6 葛明;多路串口服務器的設計與實現[D];浙江工業大學;2011年

7 薛蓮;基于ARM的串口轉以太網接口設計[D];南京理工大學;2010年

8 侯立丹;等批量孔軸零件的統計配制技術的研究及計算機實現[D];山東理工大學;2010年

，

本文編號：2035821