發布時間：2018-12-14 13:50

【摘要】：無論是水利樞紐、航運船閘、電站、防洪澇都要用到閘門,而閘門的開啟和關閉都要用到專用的機械裝置——啟閉機。與體積龐大笨重的相同容量的卷?yè)P(yáng)式啟閉機相比較,液壓式啟閉機的自重輕得多,而且水工結構布置簡單,可以節省大量投資,尤其是當孔口數量較多時此優點更為顯著。由于運行平穩,系統可方便地實現無級調速,能自動實現過載保護,易于與計算機連接,實現智能化控制等,液壓式啟閉機顯示出了其明顯的優越性。但是,液壓?jiǎn)㈤]機作為閘門啟閉主要發展方向的同時,也面臨著系統動態性能不理想、系統同步精度不高、平衡回路穩定性差等等亟需解決的諸多問題。因此,本文從問題出發,采用一種新型的同步回路結構,完成控制策略的設計并改善了系統的動態性能以及平衡回路的穩定性,為啟閉機液壓系統今后的發展提供參考。首先,簡述啟閉機液壓系統的工作原理、研究現狀、面臨的主要問題,闡述論文的研究背景和意義。第2章,詳細闡述了系統關鍵元件A11VO比例變量泵以及FD型單向節流式平衡閥的工作原理�；�于傳遞函數法分別建立了上述兩個關鍵元件的數學模型,得出方框圖,并推導出開環傳遞函數。就關鍵元件的主要結構參數變化分析其對系統動態特性的影響。根據推導出的開環增益,提出改善系統穩定性的可行方法。第3章,對液壓系統仿真軟件AMESim做了簡要介紹。利用HCD庫分別建立了同步回路和平衡回路中的兩個核心元件:A11VO比例變量泵以及FD型單向節流式平衡閥的仿真模型。驗證了模型的準確性,得出抑制比例泵出口的壓力沖擊,穩定壓力,提高系統的穩定性以及加快平衡回路系統的調節時間的方法。第4章,詳細介紹了PID控制算法各環節的作用以及參數整定方法。搭建了啟閉機液壓系統的AMESim仿真模型。結合系統模型進行了PID控制器的設計。在系統中引入PID控制器后,重點針對系統在階躍偏載和1缸階躍速度下比例泵控同步缸能否完成較為精確的位移跟隨進行仿真。觀察PID控制器的控制效果和動態性能。第5章,介紹了前饋補償控制器的工作原理,針對負載擾動的情況下,PID控制器的控制效果并不是十分的理想這一問題,通過前饋補償控制策略來消除負載變化給系統帶來的擾動。建立啟閉機液壓系統同步回路模塊的傳遞函數方框圖,在系統中引入前饋補償環節,并設計了前饋補償控制器。仿真結果表明,在相同偏載力干擾下,前饋PID控制較單純PID控制的抑制干擾能力有了明顯的改善。
[Abstract]:No matter it is a water conservancy project, a shipping lock, a power station, or a flood control station, it is necessary to use the gate, and the opening and closing of the gate must use a special mechanical device, the hoist. Compared with the large bulky hoisting hoist of the same capacity, the hydraulic hoist has much lighter weight, and the hydraulic structure is simple, which can save a lot of investment, especially when the number of orifices is more than that of the hydraulic hoist. Because of the smooth running, the system can realize stepless speed regulation conveniently, can realize the overload protection automatically, easy to connect with the computer, and realize the intelligent control, etc., the hydraulic hoist has shown its obvious superiority. However, as the main development direction of gate hoist, hydraulic hoist also faces many problems that need to be solved urgently, such as system dynamic performance is not ideal, system synchronization accuracy is not high, balance loop stability is poor, and so on. Therefore, starting from the problem, this paper adopts a new synchronous loop structure to complete the design of the control strategy and improve the dynamic performance of the system and the stability of the balance loop, which provides a reference for the future development of the hoist hydraulic system. Firstly, the working principle, research status and main problems of hydraulic system of hoist are briefly introduced, and the research background and significance of this paper are expounded. In chapter 2, the working principle of A11VO proportional variable pump and FD type unidirectional throttle balancing valve is described in detail. Based on the transfer function method, the mathematical models of the two key components are established, the block diagram is obtained, and the open loop transfer function is derived. The influence of the main structural parameters of the key components on the dynamic characteristics of the system is analyzed. According to the derived open loop gain, a feasible method to improve the stability of the system is proposed. In chapter 3, the hydraulic system simulation software AMESim is introduced briefly. The simulation models of A11VO proportional variable pump and FD type unidirectional throttle balancing valve are established by using HCD library. The accuracy of the model is verified, and the methods to suppress the pressure shock at the outlet of the proportional pump, to stabilize the pressure, to improve the stability of the system and to speed up the adjusting time of the balance loop system are obtained. In chapter 4, the function of PID control algorithm and the method of parameter tuning are introduced in detail. The AMESim simulation model of hoist hydraulic system is built. The PID controller is designed based on the system model. After the introduction of PID controller in the system, the simulation is focused on whether the proportional pump controlled synchronous cylinder can complete the more accurate displacement following under the step bias load and the step speed of 1 cylinder. Observe the control effect and dynamic performance of PID controller. In chapter 5, the working principle of feedforward compensation controller is introduced. In the case of load disturbance, the control effect of PID controller is not very ideal. The disturbance caused by load change is eliminated by feedforward compensation control strategy. The transfer function block diagram of synchronous loop module of hoist hydraulic system is established, feedforward compensation link is introduced into the system, and feedforward compensation controller is designed. The simulation results show that the performance of feedforward PID control is significantly improved than that of simple PID control under the same bias force interference.
【學位授予單位】：蘭州理工大學
【學位級別】：碩士
【學位授予年份】：2017
【分類號】：TP273;TH137

【參考文獻】

相關期刊論文 前10條

1 張氫;孫峰;鄭敬峰;秦仙蓉;孫遠韜;;基于AMESim與ADAMS的輪式裝載機聯合仿真[J];機床與液壓;2016年05期

2 劉二東;鄭建明;黃建強;賀夢婕;;直驅泵控電液位置伺服系統模糊PID控制仿真與實驗研究[J];液壓與氣動;2015年05期

3 寧辰校;張戌社;羅占興;;液壓同步回路及液壓?jiǎn)㈤]機同步控制研究[J];機床與液壓;2013年14期

4 楊國來;惠喜強;徐雙用;周淑琴;;基于AMESim的塔吊液壓頂升系統螺紋插裝式平衡閥動態特性分析[J];液壓與氣動;2013年03期

5 張小宇;;基于AMESim的液壓控制系統建模及仿真[J];煤礦機械;2011年02期

6 趙曉平;陳完成;;幾種液壓平衡回路的性能分析[J];石家莊職業技術學院學報;2009年06期

7 梁曉娟;;基于AMESim三位四通閥動態仿真研究[J];煤礦機電;2009年05期

8 江曉明;;液壓沖擊的物理本質、產生原因及其改善措施[J];科技創新導報;2009年10期

9 王炎;胡軍科;楊波;;負載敏感泵的動態特性分析與仿真研究[J];現代制造工程;2008年12期

10 張立強,楊國來,盧X;基于自適應模糊PID的徑向柱塞變量泵電液伺服控制[J];蘭州理工大學學報;2005年04期

相關博士學位論文 前1條

1 周育才;800MN巨型液壓機同步系統精良控制技術研究[D];中南大學;2012年

相關碩士學位論文 前10條

1 鄧龍;螺紋插裝式平衡閥在平衡回路中穩定性研究[D];蘭州理工大學;2016年

2 陳明明;超越負載工況下平衡閥穩定性研究[D];吉林大學;2015年

3 寧賽;電液比例泵控馬達速度控制策略研究[D];北京理工大學;2015年

4 季清華;掘進機用插裝式平衡閥動態仿真[D];太原理工大學;2013年

5 惠喜強;螺紋插裝式平衡閥動態特性和內流場的研究[D];蘭州理工大學;2013年

6 李坤;新型負載保持閥性能研究與仿真分析[D];太原科技大學;2012年

7 梁承杰;工程臂架液壓驅動同步系統設計與控制策略[D];湖南師范大學;2011年

8 梁宏喜;液壓平衡閥動態特性的數值解析[D];蘭州理工大學;2011年

9 詹磊;新型雙吊點液壓?jiǎn)㈤]機的設計與研究[D];昆明理工大學;2011年

10 張恒;負載敏感平衡閥的可視化分析及結構優化[D];太原理工大學;2010年

，

本文編號：2378716