發布時間：2018-06-20 04:03

  本文選題：雙PWM變頻調速系統 + 虛擬磁鏈��； 參考：《北京科技大學》2017年博士論文

【摘要】：交流變頻調速裝置是現代化工業自動化生產的核心設備,其性能直接影響產品的產量和質量。高性能雙PWM變頻調速系統的研發與現代化的自動化控制系統相結合,主要體現在電網側減小系統對電網的污染,保證整流側單位功率因數運行,減小網側電流諧波;負載側交流電機具備高調速精度,快速動、靜態響應和低轉矩脈振等;變頻器本身應提高系統整體運行效率,抑制直流側母線電壓波動,實現雙側能量高效轉換。本文以三相兩電平四象限雙PWM變頻器為研究對象,在分析了傳統的電流雙閉環,直接功率控制和直接轉矩控制等常規算法的基礎上,重點闡述了整流側虛擬磁鏈定向控制、逆變側無速度傳感器控制及雙側一體化協調控制綜合策略,在分析雙PWM變頻調速系統數學模型的基礎上從理論分析、仿真和實驗三個方面進行了詳細展開。本文主要研究工作為:1)對PWM整流側虛擬磁鏈方面研究,提出了自適應滑模觀測下的虛擬磁鏈直接功率控制。首先考慮到理想磁鏈應和虛擬電動勢處于完全正交關系的基礎上,設計自適應控制律來調整虛擬磁鏈補償基準,通過改進虛擬磁鏈觀測器使其快速精準的跟蹤網側電壓波動帶來的磁鏈變化,提高整流側的動態性能,并與傳統的飽和抑制法、一階低通濾波器和純積分觀測方法進行比較分析;針對虛擬磁鏈估算中的電壓計算環節,首次將滑模觀測引入PWM整流器虛擬磁鏈觀測器中,選取合適的切換函數來估計出網側電壓,并結合上述設計的自適應控制器得到虛擬磁鏈值及矢量相位角。比較傳統虛擬磁鏈定向控制策略和所提出策略的動、靜態性能,并進行仿真及實驗比較分析,最后在自主的整流器實驗平臺上進行實驗算法驗證。2)在逆變側的無速度傳感器控制算法研究與應用上,提出了加入自抗擾控制器的自適應滑模無速度傳感器控制算法。研究了基于轉子磁場定向的無速度傳感器工作原理,在傳統滑模觀測器的基礎上,引入新的雙曲正切切換函數,設計轉子位置和轉速估計的自適應律,進行了穩定性分析;考慮到電機運行過程中轉速受定子電阻變化影響,運用Lyapunov函數對定子電阻進行在線辨識。為了保證動態響應下的辨識精度,同時減小穩態誤差,利用擴張狀態觀測器實現系統動態補償線性化,設計了轉速環和電流環自抗擾控制器。仿真對比了傳統滑�？刂坪透倪M(jìn)算法的動態響應性能及速度估計的精準度,并進行電阻辨識下的仿真比較,同時以實際電驅動系統為被控對象進行實驗驗證。3)對于雙側PWM一體化協調研究,提出全響應功率補償?shù)闹苯庸β士刂撇呗浴ａ槍?duì)功率突變時的母線電壓波動問題,在整流側直接功率控制和逆變側直接轉矩控制的基礎上建立雙PWM變頻調速系統級功率平衡數學模型,通過儲能元件和耗能元件分析進行分步功率補償,仿真對比傳統PI外環的性能,并運用于硬件實驗平臺進行實驗驗證;結合雙側獨立控制研究了整流側直接功率預測控制和逆變側直接轉矩預測控制的雙側控制策略,包括一步預測和二步預測;在上述系統級功率平衡的基礎上,對雙側模型預測控制算法下的直流外環控制進行有效改進,提出基于系統級功率平衡的雙側模型預測一體化協調控制算法,并研究參數攝動下穩定性實驗分析,與傳統PI控制算法、傳統模型預測控制算法和帶有逆變側功率回饋模型預測控制算法進行對比仿真及實驗比較分析。4)開發了基于雙DSP的雙PWM變頻調速實驗平臺,研究控制電路設計和軟件設計,并在此平臺完成相關算法的實驗驗證。
[Abstract]:AC variable frequency speed regulating device is the core equipment of modern industrial automation production. Its performance directly affects the production and quality of the product. The development of high performance dual PWM variable frequency speed regulating system is combined with modern automation control system, which is mainly reflected in the pollution of the grid side reducing system to the electric network and ensuring the unit power factor of the rectifier side. In the load side, the AC motor has high speed precision, fast motion, static response and low torque pulse vibration. The frequency converter itself should improve the overall operating efficiency of the system, restrain the voltage fluctuation of the DC side bus and realize the bilateral energy efficient conversion. In this paper, a three phase two electric four quadrant double PWM inverter is used as the research object. On the basis of conventional current double closed loop, direct power control and direct torque control, this paper focuses on the directional control of the virtual magnetic chain on the rectifier side, the speed sensorless control on the inverter side and the integrated strategy of the bilateral integrated coordinated control. The theoretical analysis is based on the analysis of the mathematical model of the dual PWM variable frequency speed control system. Three aspects of simulation and experiment are carried out in detail. The main research work of this paper is: 1) research on the virtual magnetic chain on the PWM rectifier side, and put forward the direct power control of the virtual flux linkage under the adaptive sliding mode observation. Firstly, the adaptive control law is designed on the basis of the perfect relationship between the ideal magnetic chain and the virtual electromotive force. The virtual magnetic chain compensation standard is adjusted. By improving the virtual flux observer, it can quickly and accurately track the change of magnetic chain caused by the voltage fluctuation of the network side, and improve the dynamic performance of the rectifier side, and compare with the traditional saturation suppression method, the first order low pass filter and the pure integral observation method, and the voltage calculation in the virtual flux estimation. The sliding mode observation is introduced into the virtual flux observer of the PWM rectifier for the first time, and the appropriate switching function is selected to estimate the voltage of the network side, and the virtual flux and vector phase angle are obtained with the adaptive controller designed above. The dynamic and static performance of the traditional virtual magnetic chain orientation control strategy and the proposed strategy are compared and simulated. Real and experimental comparison and analysis, finally on the independent rectifier experimental platform for experimental algorithm verification.2) in the research and application of the speed sensorless control algorithm on the inverter side, an adaptive sliding mode sensorless control algorithm with auto disturbance rejection controller is proposed. The speed sensorless based on the rotor field orientation is studied. On the basis of the traditional sliding mode observer, a new hyperbolic tangent switching function is introduced to design the adaptive law of the rotor position and speed estimation, and the stability analysis is carried out. Considering that the speed of the stator is affected by the change of the stator resistance during the operation of the motor, the Lyapunov function is used to identify the stator resistance on-line. The identification precision and the steady state error are reduced. The dynamic compensation linearization of the system is realized by the extended state observer. The rotational speed loop and the current loop auto disturbance rejection controller are designed. The simulation compares the dynamic response performance of the traditional sliding mode control and the improved algorithm and the precision of the speed estimation, and compares the simulation comparison under the resistance identification. The direct power control strategy for the full response power compensation is put forward by the actual electric drive system for the controlled object of the controlled object. The direct power control strategy of the full response power compensation is proposed. The dual PWM frequency conversion is set up on the basis of direct power control of the rectifying side and the direct connection torque control of the inverter side on the basis of the problem of bus voltage fluctuation in the case of power mutation. The mathematical model of the speed system level power balance is used to simulate the performance of the traditional PI outer ring through the analysis of the energy storage element and the energy dissipation element. The performance of the traditional outer ring is simulated and compared, and the experimental verification is carried out on the hardware experimental platform. The bilateral direct power prediction control and the dual side direct torque predictive control are studied with bilateral independent control. The control strategy includes one step prediction and two step prediction. On the basis of the system level power balance, the DC outer loop control under the bilateral model predictive control algorithm is improved effectively. The dual model predictive integrated coordinated control algorithm based on the system level power balance is proposed, and the stability experiment analysis under the parameter perturbation is studied. The traditional PI control algorithm, the traditional model predictive control algorithm and the predictive control algorithm with the inverter side power feedback model predictive control algorithm are compared and compared with the experimental comparison and analysis.4. The dual DSP based dual PWM variable frequency speed regulation experimental platform is developed, and the control circuit design and software design are studied, and the experimental verification of the related algorithms is completed on this platform.
【學位授予單位】：北京科技大學
【學位級別】：博士
【學位授予年份】：2017
【分類號】：TP273

【參考文獻】

相關期刊論文 前10條

1 王東文;李崇堅;吳堯;佟寧澤;;永磁同步電機的模型預測電流控制器研究[J];電工技術學報;2014年S1期

2 李策;王京;張永康;;顯著改善異步電機動態性能的磁鏈觀測方法[J];電氣傳動;2013年09期

3 蔣連鈿;張明;莊革;于克訓;;三相PWM整流器中基于虛擬無功的鎖相環[J];電工技術學報;2013年08期

4 王麗君;童朝南;李擎;尹怡欣;高志強;鄭勤玲;;熱連軋板寬板厚的實用自抗擾解耦控制(英文)[J];控制理論與應用;2012年11期

5 王穎杰;伍小杰;戴鵬;朱榮伍;;采用參數辨識及新型主動阻尼控制的LCL濾波脈寬調制整流器[J];中國電機工程學報;2012年15期

6 王明渝;代同振;吳喜紅;鄧威;;雙PWM變換器功率前饋控制策略仿真研究[J];系統仿真學報;2012年04期

7 王麗君;童朝南;李擎;尹怡欣;高志強;鄭勤玲;;實用自抗擾控制在大時滯厚度自動監控系統中的應用[J];控制理論與應用;2012年03期

8 戴鵬;朱方田;朱榮伍;陳根;;電容電流直接控制的雙PWM協調控制策略[J];電工技術學報;2011年S1期

9 張巍;尚曉磊;周元鈞;劉欣博;韓紅偉;;一種適用于航空電力作動器負載的三相PWM整流器最大功率控制[J];電工技術學報;2011年08期

10 王宏佳;徐殿國;楊明;;永磁同步電機改進無差拍電流預測控制[J];電工技術學報;2011年06期

相關博士學位論文 前6條

1 陸駿;永磁同步電機無傳感器直接轉矩控制的研究[D];東華大學;2016年

2 吳軒欽;電勵磁同步電機雙三電平矢量控制系統研究及其應用[D];中國礦業大學;2011年

3 孔維濤;繞組勵磁同步電機無傳感器矢量控制的研究[D];山東大學;2009年

4 陳偉;三相電壓型PWM整流器的直接功率控制技術研究與實現[D];華中科技大學;2009年

5 魏學森;大功率三電平矢量控制系統研究[D];天津大學;2005年

6 張興;PWM整流器及其控制策略的研究[D];合肥工業大學;2003年

相關碩士學位論文 前2條

1 田士俠;高頻注入法永磁同步電機轉子位置檢測方法研究[D];山東大學;2010年

2 姜雪松;三相高功率因數可逆整流器研究[D];南京航空航天大學;2002年

，

本文編號：2042863