發布時間：2018-01-04 14:45

  本文關鍵詞：導流器幾何參數對潛水泵性能的影響　出處：《蘭州理工大學》2012年碩士論文　論文類型：學位論文

  更多相關文章： 潛水泵 導流器 水力設計 數值模擬 內部流場分析 面積比

【摘要】：潛水泵作為一種通用機械廣泛應用于工農業生產生活中，，但是目前市場上的潛水泵機組效率普遍不夠高，所以有必要研究開發性能更優的潛水泵。設計中除改進葉輪外還可以通過改變導流器幾何參數來生產出性能更加優異的潛水泵，適應市場需求。 本課題以潛水泵作為研究對象，通過對潛水泵全流場水力設計、過流部件三維造型并運用CFD數值模擬技術對潛水泵導流器特性及提高泵性能展開研究，對其性能進行了預測與分析，取得的研究成果如下: 第一，推導了導流器及葉輪的特性方程式，理論上分析出了導流器幾何參數葉片數Z、軸面進口寬度b3及葉片進口安放角α3對導流器特性曲線的影響,得到了潛水泵最佳工況點的理論求解方法； 第二，采用FLUENT軟件，選用kε模型，利用SIMPLE算法對潛水泵內部三維不可壓縮湍流場在不同流量運行工況下進行了數值計算預估。通過對不同進口幾何參數導流器方案的速度場、壓力場的分析研究，預測出了導流器的性能。 第三，通過對同一葉輪分別與不同進口幾何參數導流器匹配的潛水泵進行的數值計算得到了各潛水泵的性能曲線，并根據沿軸線方向不同Z截面總壓平均量變化曲線計算出了不同方案導流器的內部能量損失，揭示了導流器葉片數Z、軸面進口寬度b3及葉片進口安放角α3對泵性能影響規律； 第四，通過對解析法計算所得的潛水泵最佳工況點與數值模擬試驗所得的最佳工況點進行的誤差分析，論證了潛水泵最佳工況點的理論計算方法和CFD數值模擬結果是吻合的，有實用價值的； 第五，利用潛水泵面積比系數的理論計算與實測方法，計算出同一葉輪與不同幾何參數導流器匹配時面積比系數，并結合導流器幾何參數Z、b3、α3對泵性能影響規律得到了250QJ125型潛水泵的最佳面積比系數最佳取值范圍為0.84~0.86。并在保持葉輪不變情況下，根據研究出的結論設計出一種新的導流器(Ⅱ)，通過分析得到潛水泵(Ⅱ)的單級揚程及效率較原型泵(Ⅰ)分別提高了0.9m和1.96%，從而證明了本課題研究是有價值的； 借助CFD數值模擬技術研究潛水泵導流器的特性及泵性能，能夠清晰得掌握潛水泵內部流動規律，從而判斷設計參數是否合理；同時還可以縮短產品研發周期，降低成本，具有較大的科研和經濟意義。
[Abstract]:Submersible pump as a kind of general machinery is widely used in industrial and agricultural production and life, but the efficiency of submersible pump units in the market is generally not high enough. So it is necessary to study and develop submersible pump with better performance. In addition to improving impeller, it is possible to produce submersible pump with better performance by changing the geometric parameters of the guide so as to meet the needs of the market. This topic takes submersible pump as the research object, through the hydraulic design of the whole flow field of the submersible pump, the three-dimensional modeling of the flow passing parts and the use of CFD numerical simulation technology to study the characteristics of the submersible pump guide and improve the pump performance. Its performance is predicted and analyzed, and the research results are as follows: Firstly, the characteristic equations of the guide and impeller are derived, and the influence of the geometric parameters of the guide on the characteristic curve of the guide is analyzed theoretically, such as the number of blades Z, the width of the axial inlet b _ 3 and the angle 偽 _ 3 of the inlet of the blade. The theoretical solution of the optimal operating point of the submersible pump is obtained. Secondly, we adopt FLUENT software and choose k 蔚 model. The 3-D incompressible turbulent field in submersible pump was calculated and predicted by SIMPLE algorithm under different flow operating conditions. The velocity field of different inlet geometric parameter diversion schemes was calculated and predicted. The performance of the guide is predicted by the analysis of the pressure field. Thirdly, the performance curves of each submersible pump are obtained by the numerical calculation of the same impeller matching with different inlet geometric parameters of the submersible pump. According to the variation curve of the total pressure of different Z section along the axis, the internal energy loss of the diversion device with different schemes is calculated, and the blade number Z of the diversion device is revealed. The influence of axial inlet width b3 and blade inlet angle 偽 3 on pump performance; 4th, the error analysis of the optimum operating point of submersible pump calculated by analytical method and the optimum working point obtained by numerical simulation test is carried out. It is proved that the theoretical calculation method of the optimum operating point of submersible pump is in agreement with the result of CFD numerical simulation and has practical value. In 5th, the area ratio coefficient of the same impeller matched with different geometric parameters was calculated by using the theoretical calculation and the actual measurement method of the area ratio coefficient of the submersible pump, and combined with the geometric parameter ZB3 of the diversion device. The optimum area ratio coefficient of the 250QJ125 submersible pump was obtained from the effect of 偽 3 on the pump performance in the range of 0.84V 0.86, and the impeller was kept unchanged. According to the conclusion of the study, a new type of diversion (鈪

本文編號：1378836