重載鐵路車—軌—橋系統垂向建模及動力性能優化
發布時間：2019-06-14 00:50
【摘要】：重載鐵路運輸提速、大軸重、長編組的發展需求,對車-軌-橋系統的安全性和耐久性提出了更高的要求,建立動力學仿真模型研究車-軌-橋系統動力學響應并進行優化,可以為線路設計提供相關設計依據以滿足其發展需求。本文將車輛視為多剛體系統,推導了重載鐵路有砟軌道-橋梁有限單元方程,采用赫茲非線性輪軌關系建立了重載鐵路車-軌-橋系統垂向動力學模型,編制Matlab程序?qū)崿F(xiàn)了車-軌-橋系統動力響應的迭代求解,并與實測數據進行對比驗證了模型的可靠性。隨后選取了車輛、軌道、橋梁參數,進行車-軌-橋系統動力學仿真分析,研究了不同軌道結構參數下系統響應峰值的變化規律�；谠撟兓�(guī)律,設立單目標、多目標動力響應優化工況,采用Pareto排序的遺傳算法優化方法對車-軌-橋系統動力性能進行優化,得到不同工況下最優參數取值。通過研究得出以下主要結論:(1)軌道結構參數的變化對車-軌-橋系統各部件響應峰值具有不同程度的影響。當軌下墊層剛度kp和道床厚度hb發生變化時,主要影響鋼軌、軌枕、道床垂向加速度、速度響應峰值,尤其是垂向加速度響應峰值,對橋梁響應峰值影響不大,且對整個系統垂向位移響應影響不大。(2)單類動力響應峰值優化結果表明,鋼軌加速度響應峰值最小時,軌下墊層剛度kp為160 MN/m,道床厚度hb為0.31m;道砟塊加速度響應峰值最小時,軌下墊層剛度kp為60 MN/m,道床厚度化為0.60m。不同優化結果相互比較時,軌下墊層剛度kp或道床厚度hb的最優取值存在差異,實際工程中需兼顧系統響應水平。(3)多類動力響應峰值的優化結果表明,鋼軌加速度響應與軌枕加速度響應,或鋼軌加速度響應與道砟塊加速度響應組合時,軌下墊層合理剛度kp為180MN/m,道床合理厚度hb為0.39m,軌枕加速度響應與道砟塊加速度響應組合時,軌下墊層合理剛度kp為160MN/m,道床合理厚度hb為0.60m。本文從車-軌-橋系統動力學響應的角度出發,結合不同優化目標給出了道床厚度、軌下墊層剛度參考取值。(4)在優化效率方面,本研究針對每個工況獨立重復優化3次,3次優化結果保持一致,說明了本文所提出的遺傳算法可以實現車-軌-橋系統動力性能的優化,且優化效率顯著。
[Abstract]:The development demand of speed increase, large axle load and long marshalling of heavy load railway transportation puts forward higher requirements for the safety and durability of vehicle-rail-bridge system. The dynamic simulation model is established to study and optimize the dynamic response of vehicle-rail-bridge system, which can provide the relevant design basis for line design to meet its development needs. In this paper, the vehicle is regarded as a multi-rigid-body system, and the finite element equation of ballasted track-bridge of heavy-duty railway is derived. the vertical dynamic model of heavy-duty railway vehicle-rail-bridge system is established by using Hertz nonlinear wheel-rail relationship. The iterative solution of dynamic response of vehicle-rail-bridge system is realized by Matlab program, and the reliability of the model is verified by comparing with the measured data. Then the vehicle, track and bridge parameters are selected to simulate the dynamics of the vehicle-rail-bridge system, and the variation of the peak value of the system response under different track structure parameters is studied. Based on the change law, the single objective and multi-objective dynamic response optimization conditions are set up, and the dynamic performance of the vehicle-rail-bridge system is optimized by using the genetic algorithm optimization method of Pareto ranking, and the optimal parameters under different working conditions are obtained. The main conclusions are as follows: (1) the change of track structure parameters has different degrees of influence on the response peak value of each component of the vehicle-rail-bridge system. When the rail underlying stiffness kp and the track bed thickness hb change, the rail, sleeper, track bed vertical acceleration, velocity response peak value, especially the vertical acceleration response peak value, has little effect on the bridge response peak value, and has little effect on the vertical displacement response of the whole system. (2) the peak value of rail acceleration response is the smallest, and the rail underlying cushion stiffness kp is 160 MN/m,. (2) the peak value of rail acceleration response is the smallest, and the rail underlying layer stiffness kp is 160 MN/m,. The thickness of track bed hb is 0.31m; The peak acceleration response of the ballast block is the smallest, and the stiffness of the underlying layer of the rail kp is 60 MN/m, and the thickness of the track bed is 0.60 m. When different optimization results are compared, the optimal values of rail underlying stiffness kp or track bed thickness hb are different, and the system response level should be taken into account in practical engineering. (3) the optimization results of multiple kinds of dynamic response peaks show that when the rail acceleration response and sleeper acceleration response, or the combination of rail acceleration response and ballast block acceleration response, the reasonable stiffness kp of rail underlying layer is 180mm, and the reasonable thickness hb of track bed is 0.39m. When the acceleration response of sleeper and ballasted block is combined, the reasonable stiffness kp of underlying layer is 160mn m, and the reasonable thickness of track bed hb is 0.60m. In this paper, from the point of view of dynamic response of vehicle-rail-bridge system, combined with different optimization objectives, the reference values of track bed thickness and cushion stiffness under rail are given. (4) in terms of optimization efficiency, the optimization results of three times of independent repeated optimization for each working condition are consistent, which shows that the genetic algorithm proposed in this paper can optimize the dynamic performance of vehicle-rail-bridge system, and the optimization efficiency is remarkable.
【學位授予單位】：北京交通大學
【學位級別】：碩士
【學位授予年份】：2017
【分類號】：U211;U441.7;U239.4
本文編號：2498961
[Abstract]:The development demand of speed increase, large axle load and long marshalling of heavy load railway transportation puts forward higher requirements for the safety and durability of vehicle-rail-bridge system. The dynamic simulation model is established to study and optimize the dynamic response of vehicle-rail-bridge system, which can provide the relevant design basis for line design to meet its development needs. In this paper, the vehicle is regarded as a multi-rigid-body system, and the finite element equation of ballasted track-bridge of heavy-duty railway is derived. the vertical dynamic model of heavy-duty railway vehicle-rail-bridge system is established by using Hertz nonlinear wheel-rail relationship. The iterative solution of dynamic response of vehicle-rail-bridge system is realized by Matlab program, and the reliability of the model is verified by comparing with the measured data. Then the vehicle, track and bridge parameters are selected to simulate the dynamics of the vehicle-rail-bridge system, and the variation of the peak value of the system response under different track structure parameters is studied. Based on the change law, the single objective and multi-objective dynamic response optimization conditions are set up, and the dynamic performance of the vehicle-rail-bridge system is optimized by using the genetic algorithm optimization method of Pareto ranking, and the optimal parameters under different working conditions are obtained. The main conclusions are as follows: (1) the change of track structure parameters has different degrees of influence on the response peak value of each component of the vehicle-rail-bridge system. When the rail underlying stiffness kp and the track bed thickness hb change, the rail, sleeper, track bed vertical acceleration, velocity response peak value, especially the vertical acceleration response peak value, has little effect on the bridge response peak value, and has little effect on the vertical displacement response of the whole system. (2) the peak value of rail acceleration response is the smallest, and the rail underlying cushion stiffness kp is 160 MN/m,. (2) the peak value of rail acceleration response is the smallest, and the rail underlying layer stiffness kp is 160 MN/m,. The thickness of track bed hb is 0.31m; The peak acceleration response of the ballast block is the smallest, and the stiffness of the underlying layer of the rail kp is 60 MN/m, and the thickness of the track bed is 0.60 m. When different optimization results are compared, the optimal values of rail underlying stiffness kp or track bed thickness hb are different, and the system response level should be taken into account in practical engineering. (3) the optimization results of multiple kinds of dynamic response peaks show that when the rail acceleration response and sleeper acceleration response, or the combination of rail acceleration response and ballast block acceleration response, the reasonable stiffness kp of rail underlying layer is 180mm, and the reasonable thickness hb of track bed is 0.39m. When the acceleration response of sleeper and ballasted block is combined, the reasonable stiffness kp of underlying layer is 160mn m, and the reasonable thickness of track bed hb is 0.60m. In this paper, from the point of view of dynamic response of vehicle-rail-bridge system, combined with different optimization objectives, the reference values of track bed thickness and cushion stiffness under rail are given. (4) in terms of optimization efficiency, the optimization results of three times of independent repeated optimization for each working condition are consistent, which shows that the genetic algorithm proposed in this paper can optimize the dynamic performance of vehicle-rail-bridge system, and the optimization efficiency is remarkable.
【學位授予單位】：北京交通大學
【學位級別】：碩士
【學位授予年份】：2017
【分類號】：U211;U441.7;U239.4
【參考文獻】
相關期刊論文 前10條
1 沈彬然;周昌盛;曾曉輝;王平;;鋼軌重型化對輪軌系統動力響應及動力傳遞的影響[J];鐵道建筑;2015年11期
2 玄登影;王福林;高敏慧;馬海志;;一種改進適應度函數的遺傳算法[J];數學的實踐與認識;2015年16期
3 ZHANG Nan;ZHOU Shuang;XIA He;SUN Lu;;Evaluation of vehicle-track-bridge interacted system for the continuous CRTS-II non-ballast track slab[J];Science China(Technological Sciences);2014年10期
4 卓卉;;國外重載鐵路運輸進展與我國重載鐵路運輸分析[J];中國煤炭;2014年S1期
5 孫文靜;周勁松;宮島;;基于Timoshenko梁模型的車輛-軌道耦合系統垂向隨機振動分析[J];機械工程學報;2014年18期
6 倪旭瀾;謝小海;;世界主要大國重載鐵路運輸?shù)陌l(fā)展及其作用[J];國外機車車輛工藝;2014年04期
7 徐磊;陳憲麥;李曉健;孟憲洪;;朔黃重載鐵路軌道不平順譜分析[J];中南大學學報(自然科學版);2013年12期
8 陳伯靖;錢小益;秦超紅;李成輝;;鐵路鋼軌受力分析模型比較研究[J];工程力學;2013年06期
9 李運生;安立朋;魏樹林;張德瑩;;重載列車作用下鐵路鋼桁梁橋的動力響應分析及疲勞壽命評估[J];石家莊鐵道大學學報(自然科學版);2012年04期
10 高亮;辛濤;肖宏;曲村;;高速鐵路橋上不同軌枕型式動力特性對比[J];同濟大學學報(自然科學版);2012年01期
相關重要報紙文章 前1條
1 徐春明;;186天，，30噸軸重貨車走行10萬公里[N];科技日報;2015年
相關博士學位論文 前1條
1 程方曉;基于自適應保持多樣性遺傳算法的汽車動力傳動系多目標優化[D];吉林大學;2011年
相關碩士學位論文 前2條
1 閆曉夏;朔黃鐵路超低高度預應力混凝土梁重載改造技術研究[D];中國鐵道科學研究院;2014年
2 李浩宇;重載鐵路線路參數分析及其行車動力特性研究[D];石家莊鐵道大學;2014年
本文編號：2498961
本文鏈接：http://www.wukwdryxk.cn/kejilunwen/daoluqiaoliang/2498961.html
